How to Choose Flood Barriers: Modular Water Boards
Underground car parks, shop entrances and basement doorways fear rainwater pouring in during a storm. Sandbags can block it, but stacking them takes time and effort; a modular flood barrier stores flat and takes minutes to put up, with better height and sealing than a sandbag wall. This guide explains how to choose a modular flood barrier, measure for it and check its seal.
Know the Standards First: There Is No National Standard Yet
There is currently no national standard for modular flood barrier boards; purchase and acceptance mainly follow group standards and enterprise standards. Two relevant group standards are:
- T/CHES, Technical Specification for Modular Metal Flood Barriers, a group standard of the Chinese Hydraulic Engineering Society, covering design and manufacture, installation, removal, transport, storage and maintenance of modular metal flood barriers, for raising concrete levees and for flood walls in cities, industrial and mining areas, important buildings and other areas, with barrier heights up to 2.5 m.
- T/GDJSKB 011-2023, Modular Aluminium Alloy Flood Barrier Walls, a standard of the Guangdong Construction Technology and Standardisation Association, issued 19 July 2023 and in force from 1 September 2023, for barrier structures made from aluminium alloy profiles, used at building entrances, riverbanks and other areas needing water blocking.
No national standard does not mean no basis for acceptance. Write the applicable standard, material, barrier height and sealing requirements into the contract, and check them one by one against the contract and test reports at acceptance. The performance of aluminium alloy profiles can be checked against general standards such as GB/T 5237, Aluminium Alloy Building Profiles, and GB/T 3190, Chemical Composition of Wrought Aluminium and Aluminium Alloys.
How the Structure Works
A modular flood barrier is made of barrier boards, posts, sealing strips, clamping devices, connectors and pre-set foundations, and can be assembled and removed quickly. When buying, check these parts:
- Barrier boards: usually aluminium alloy profiles. The heavy-duty modular aluminium flood barrier commonly stocked on this site uses 6063-T6 aluminium alloy, 50 mm thick, with each board 200 mm high and a maximum barrier height of 1,200 mm. Board thickness decides water-pressure resistance — the thicker the board and the stronger the profile, the higher the water level it can hold back.
- Posts: the posts support the barrier boards, and post spacing and fixing decide overall strength. Posts must work with the pre-embedded parts in the ground, and must be fixed firmly when installed, with no wobble.
- Sealing strips: needed between boards, between boards and the ground, and between boards and posts, usually EPDM rubber. Sealing strip quality decides whether water leaks — aged or deformed strips must be replaced promptly.
- Clamping devices: press the barrier boards tight against the posts and the ground to keep the seal. They must be simple to operate, so one person can work them during a flood.
- Pre-embedded parts: fixings must be embedded in the ground and the walls on both sides, out of the way of traffic normally, and ready for barrier boards when a flood comes. Pre-embedded parts should be installed during decoration or construction — adding them afterwards takes time and effort.
How to Measure the Size
Barrier size must be measured on site — do not guess:
- Width: measure the actual width of the doorway or passage — the clear width between the walls on both sides. The barrier length must match the clear width, leaving room for the posts.
- Barrier height: set it by the highest historical water level plus a margin. For an underground car park entrance, the barrier height should generally be above the highest historical flood level, with a safety margin. The heavy-duty modular aluminium flood barrier stocked on this site has a maximum barrier height of 1,200 mm, with each board 200 mm high, so height is set by stacking boards.
Once measured, the barrier is made to size, with posts, sealing strips and clamping devices supplied as a set.
Installation and Acceptance
Practise installation before use. Do not put a barrier straight into the warehouse after buying it — install it once at the actual location to confirm the size is right, the posts are firm, the seal is tight, and one person can install it. Time the practice run: the speed of installation during a flood is the speed of the practice run, and someone who has never practised cannot learn it in a flood.
At acceptance, do a sealing check: once the barrier is installed, splash water on the water-facing side or run a water-blocking test, and check the board joints, the board-to-ground joints and the board-to-post joints for leaks. Adjust the sealing strips and clamping devices where there is leakage, until nothing leaks.
Do a full check before flood season: whether the boards are deformed or corroded, whether the sealing strips have aged, whether the clamping devices move freely, and whether the pre-embedded parts are firm. As soon as a rainstorm warning comes, install the barrier — do not wait until water is already in the car park.
Use with Sandbags and Pumps
A flood barrier is not a cure-all — use it together with sandbags and pumps. The barrier holds back the main water at entrances, sandbags seal small gaps such as door seams and window wells, and pumps drain the water that seeps or flows in. Only the three together make flood control complete.
With only a barrier and no pump, water seeping in from elsewhere cannot be drained; with only a pump and no barrier, water comes in faster than it can be pumped out, and no pump can keep up. Blocking and drainage must be stocked together, and blocking and drainage should be drilled before flood season to confirm both work.
Frequently Asked Questions
How is the barrier height set?
Set it by the highest historical water level plus a margin. For an underground car park entrance, the barrier height must be above the highest historical flood level. The heavy-duty modular aluminium flood barrier stocked on this site has a maximum height of 1,200 mm, with each board 200 mm high, stacked to the height needed.
How long does installation take?
A practised person can install it in minutes, provided the sizes all match and it has been practised. Someone who has never practised cannot learn it in a flood — install it once at the actual location after buying and time the practice run.
Which is better, a flood barrier or sandbags?
Each has its strengths. A barrier installs fast, seals well and holds back a higher water level, suited to fixed points; sandbags are flexible and cheap, suited to temporary sealing and wide-area defence. Used together they work best.
How often should a flood barrier be checked?
Do a full check before flood season: whether the boards are deformed or corroded, whether the sealing strips have aged, and whether the clamping devices move freely. Check monthly during flood season, and count and top up after the season.