Category: Labor Protection Supplies

How to Choose a Dust Mask: A Guide for Dusty Work

Grinding, cutting, drilling, sweeping and handling powders — dust is everywhere on industrial sites. Ordinary gauze masks and disposable flat masks cannot stop fine dust; dust breathed into the lungs cannot be expelled, and long-term build-up causes occupational diseases such as pneumoconiosis. A dust mask is the most basic protection for dusty work — the wrong model is the same as no protection. This guide explains dust mask selection under the current standard.

Know the Standard First: GB 2626-2019 Is the Current Version

The current mandatory national standard for industrial dust masks is GB 2626-2019, Respiratory Protection — Self-Priming Filter-Type Particulate Respirators, issued 31 December 2019 and in force from 1 July 2020. The formal name in the standard is "self-priming filter-type particulate respirator" — what people usually call a dust mask or particulate respirator is this product.

The standard divides filter elements into KN and KP classes by filtration performance. KN class filters non-oily particles only, in three grades: KN90, KN95 and KN100; KP class filters oily and non-oily particles, in three grades: KP90, KP95 and KP100. The number is the minimum filtration efficiency: grade 90 is at least 90%, grade 95 at least 95%, and grade 100 at least 99.97%.

Two points to remember: KN class cannot be used in oily-particle environments, while KP class can replace KN class in non-oily environments; a mask should be marked with the standard number plus the class, for example "GB 2626-2019 KN95". Be cautious of a mask that only says "KN95" without the standard number, or with the wrong standard number.

Choose the Grade by Dust Type

Different dusts are more or less hazardous, so the grade differs. Following the selection advice commonly used in the industry:

  • General dust, such as wood dust, coal dust and ordinary construction dust: filtration efficiency of at least KN90.
  • High-hazard dust such as asbestos dust and glass fibre: at least KN95.
  • Heavy-metal dust (such as lead and manganese dust), silica dust, arsenic dust, and welding fume and foundry fume: at least KN95.
  • Oily particles, such as coke-oven fume, asphalt fume and oil mist: at least KP95 — KN class cannot be used.
  • Radioactive particles: at least KN100.

A higher grade filters better, but breathing resistance rises too. Selection is not about going as high as possible, but about enough: KN90 is enough for general dust work, while forcing KN100 makes breathing hard and workers unwilling to wear it. If the dust type and concentration are uncertain, run occupational hygiene tests first and select by the results.

Style and Wearing: Fit Decides Everything

Dust masks come in disposable styles and replaceable half-facepiece styles. Disposable masks are thrown away after use, suited to low dust concentrations and short work; replaceable half-facepieces take replaceable filter cartridges, suited to high dust concentrations and long work. A valved mask has lower exhalation resistance and feels less stuffy, suited to heavy physical work — but the valve only lets air out and does not filter it, so exhaled air passes unfiltered.

However good the mask, a poor seal is the same as no mask. When wearing one, note:

  • The mask must fully cover the mouth, nose and chin, the nose clip pressed tight against the nose bridge, with no gaps at the sides.
  • Do a seal check before wearing: cover the mask with both hands and breathe in sharply — the mask should pull inward with no sense of leakage; when breathing out, no air should leak at the edges.
  • Facial hair affects the seal — posts that need dust masks should keep the face where it contacts the mask clean and free of beard.
  • Replace the mask immediately when it is damaged, soiled or deformed, or when breathing resistance rises noticeably.

What to Check at Acceptance and in Management

  • Check the LA mark. A dust mask is a special labour protection product and should carry the special labour protection safety mark (LA mark) and a certificate number.
  • Check the test report. The model, manufacturer and standard number on the report must match the delivered product.
  • Mind the expiry date and storage. Masks should be stored clean, dry and ventilated, away from direct sunlight and contamination; do not use expired masks.
  • Set up issue and replacement rules. Disposable masks are generally changed after 8 hours of cumulative use, or when damaged or soiled; filter cartridges for replaceable half-facepieces are changed regularly per the manufacturer's instructions.

Frequently Asked Questions

Can a KN95 mask stop all dust?

No. KN95 only stops non-oily particles — oily particles (oil mist, asphalt fume) need KP95 or above. KN95 also cannot stop toxic gases or vapours; a toxic-gas environment needs a gas mask.

Can a dust mask be reused?

A disposable mask is single-use — replace it when damaged, soiled or when breathing resistance rises noticeably, and do not wash and reuse it. A replaceable half-facepiece body can be reused, but its filter cartridges must be changed regularly.

Does a valved mask protect less well?

The valve does not affect filtration when breathing in, so protection is the same as a valveless mask of the same class. The valve only lowers exhalation resistance and stuffiness.

Can a dust mask be used in an oxygen-deficient environment?

No. A dust mask only filters particles from the air — it cannot supply oxygen. In an environment below 19.5% oxygen, supplied-air respiratory protection must be used.

WhatsApp 18300232331 Get a Free Quote
Chat Get a Quote