How to Choose Protective Suit Sizes: Fit and Movement
Choose the wrong size of protective suit and even the best protection is wasted: too big and hems and cuffs catch in machines, too small and bending over or raising an arm tears the seams — and workers simply stop wearing it. Protective suit sizes cannot be bought by everyday clothing habits; they must be set by size code, by range of movement, and by what is worn underneath.
How to Read a Size Code: What Does 175/92A Mean?
Clothing sizes in China follow GB/T 1335.1-2008, Garment Sizes — Men, and GB/T 1335.2-2008, Garment Sizes — Women. A size code is written as "size/type + body type" — for example 175/92A: 175 is the size, meaning a height of 175 cm, with height in 5 cm steps; 92 is the type, meaning a net chest of 92 cm for a top, or a net waist for bottoms; A is the body type, divided by chest-waist difference into Y, A, B and C.
The chest-waist difference ranges are, for men's wear: Y (slim) 17 to 22 cm, A (normal) 12 to 16 cm, B (stout) 7 to 11 cm, C (corpulent) 2 to 6 cm; for women's wear: Y (slim) 19 to 24 cm, A (normal) 14 to 18 cm, B (stout) 9 to 13 cm, C (corpulent) 4 to 8 cm. Body type A is the most common, but a company buying in bulk cannot assume everyone is type A — slimmer and heavier staff must report their body type separately.
The same "L" can differ by several centimetres in chest size between manufacturers. Before buying, ask the supplier for a size chart giving the garment length, chest, shoulder width and sleeve length for each size, and have staff report their size code against that chart — not just S, M, L or XL.
Why Everyday Sizes Do Not Work for Protective Suits
More clothing is usually worn inside a protective suit: thick underwear and sweaters in winter, and workwear inside a chemical suit. Buying by everyday size leaves the suit tight once the inner layers are on. Before buying, confirm whether the suit is worn on its own or over other clothing — over-clothing needs room for what is inside.
A protective suit also needs room to move. Workers wearing one must bend, raise their arms, squat and climb ladders — a suit that is too tight makes these movements impossible, or tears seams and pops buttons when they are attempted. One-piece suits need particular care at the crotch and armpits, where tearing happens most easily.
Different types of protective suit also fit differently: disposable suits are mostly loose-fitting, chemical and flame-retardant suits are mostly close-fitting, and cold-weather suits need room for insulation layers. Do not apply one suit's sizing experience to another type.
How to Measure and Count Sizes
Size counting must collect each worker's height, weight, net chest and net waist, converted into size codes for the order. The form is issued centrally by administration and collected back from each department, with a 100% return rate — a worker who is missed has no suit when the goods arrive, and a replacement order takes another round.
When measuring, note: net chest is measured without an outer coat, breathing naturally; waist is measured at its narrowest point, neither pulled tight nor left with too much slack. The classic measuring error is measuring in a sweater in winter and a vest in summer — the same person's figures differ by several centimetres, so the measuring standard must be uniform.
Handle special builds separately: staff taller than 185 cm, overweight or very slim should report their size separately, with custom sizing where needed. Do not squeeze special builds into regular sizes to save trouble — a poor fit hurts both protection and comfort.
Fitting Checkpoints
Before a bulk order, take samples and have staff of different builds try them on, checking these points: raising the arms overhead, the cuffs should not ride above the wrists; squatting fully, the crotch should not pull tight and the lower back should not show; bending 90 degrees, the garment length should cover the waist; with buttons or zipper closed, the chest should not pull tight, leaving about a fist of room; walking and climbing ladders, hems and trouser legs should not drag or trip the wearer.
If fitting finds a problem, adjust the size chart or change the cut promptly — do not wait until the bulk goods arrive. Keep the fitting records as a reference for acceptance.
For donning and doffing, see How to Put On and Take Off a Protective Suit Safely.
Frequently Asked Questions
Is buying one size up safer?
No. A bigger size is easier to move in, but over-long cuffs and hems can catch in machines or trip the wearer, and can snag at height. The right size plus enough room to move is correct — bigger is a hazard, not insurance.
How do S, M and L map to size codes?
There is no unified mapping — it differs by manufacturer and style. When buying, use the supplier's size chart and have staff report their size code, not just S, M or L.
Is there a dedicated standard for protective suit sizing?
Clothing sizes follow the GB/T 1335 series. The general technical specification for protective clothing is GB 20097-2025, Protective Clothing — General Technical Specification, in force from 1 September 2026, replacing GB/T 20097-2006 and GB/T 13640-2008 — check it as well when buying protective suits.
What if a worker's weight changes?
Re-count sizes once a year, and count separately when staff change or new workers join. Do not order from last year's size table — weight changes and staff turnover make the old table wrong.