Category: Labor Protection Supplies

How to Choose a Safety Harness: Fall Protection Guide

A fall from height is one of the deadliest workplace accidents, and the harness is the first line of defence against it. Choose the wrong harness type, the wrong rope or the wrong anchor point, and wearing it is the same as not wearing one. This guide explains the three harness types, the current standard and the matching gear, so buyers can choose fall protection by the job.

Know the Standard First: GB 6095-2021 Is the Current Version

Safety harnesses for work at height follow GB 6095-2021, Fall Protection — Safety Harness, published 10 August 2021 and in force from 1 September 2022, replacing GB 6095-2009. The standard applies to fall-protection harnesses where the user's body weight plus load is no more than 100 kg. Write the 2021 edition on purchase contracts and acceptance forms — the 2009 edition has been abolished.

Safety ropes follow GB/T 24543, Fall Protection — Safety Rope, and fire-service fall-protection equipment follows XF 494-2023, Fire Service Fall Protection Equipment. Note the distinction: fire safety ropes and industrial safety ropes are two different systems — fire ropes follow XF 494-2023 and industrial ropes follow GB/T 24543. Do not mix them when buying; an industrial safety rope must not be used as a fire safety rope.

Three Harness Types: By How the Work Is Done

  • Work-positioning harness: for pole work on utility poles and towers — a belt plus a positioning lanyard, leaving both hands free, with fall protection from the lanyard fixed to the pole.
  • Restraint harness: it limits the range of movement so the user cannot reach a fall edge, suited to roofs, platform edges and similar work, preventing the person from reaching the danger point by limiting the length.
  • Fall-arrest harness: a full-body harness worn with an energy absorber or a self-retracting lifeline, which holds the person suspended after a fall, suited to scaffolding, tower cranes, exterior walls and other work at height with a fall risk.

Choose by how the work is done first: pole work calls for the positioning type, work near an edge calls for restraint, and any work with a fall risk calls for fall arrest. Then consider the fall height and the anchor conditions — the higher the anchor, the shorter the fall distance and the safer the setup.

What Goes with a Harness: Rope, Absorber, Anchor

  • Safety rope: it connects the harness to the anchor point, with its length set by the working range; industrial safety ropes follow GB/T 24543.
  • Energy absorber and self-retracting lifeline: they absorb the fall impact. Fall arrest must include one — without a shock-absorbing device, the fall force passes straight into the body.
  • Anchor point: it must be able to take the fall-arrest force, fixed to a solid structure. Never anchor to pipes, railings or moving parts that cannot bear the load, and keep the anchor as high as possible.
  • Fire scenes use fire safety rope: the Dong'an FZL-S-Q9.5 light safety rope, 20 m, has a minimum breaking strength of at least 20 kN and shows no melting or charring after a 204 °C test, suited to firefighters' personal escape and self-rescue; the general ropes FZL-S-T16 and FZL-S-T13.5 are thicker and stronger, suited to rescue lifting. The FZL-T-QZJ escape set contains a rope, a descender and a harness, suited to escape from high-rise buildings.

Acceptance and Use

  • Check the test report. The model, manufacturer and standard number on the report must match the delivered product, and the report must be within its validity period.
  • Inspect the webbing, stitching and metal parts. Check webbing for wear, cuts and burns, stitching for loose threads, and metal parts for deformation, rust and cracks.
  • Check the absorber and connectors. Energy absorbers, self-retracting lifelines and hooks must work properly, and snap hooks must lock automatically.
  • Try it on and adjust the fit. Shoulder, leg and waist straps should fit the body without pinching, with free movement; too loose and the wearer can slip out in a fall, too tight and work is hampered.
  • Inspect regularly and retire on schedule. Check the appearance before every use, do a full inspection every quarter, and a full test once a year under the standard; a harness or rope that has taken one fall must be retired at once — even if it looks undamaged, the internal fibres may already be damaged.
  • Store dry, ventilated and away from light, away from chemicals and sharp tools, and do not leave it in long-term sun — ultraviolet light ages webbing faster.

For fire escape ladders, see Fire Escape Ladder: How to Choose Length, Load, Anchoring.

Common Mistakes

  • Having a rope means having protection. A safety rope only works as a set with a harness, an anchor point and an absorber — a rope alone cannot give complete protection.
  • A belt-type harness works anywhere. A belt type suits only work positioning and restraint — work with a fall risk needs a full-body fall-arrest harness.
  • Anchoring anywhere will do. If the anchor is not solid, it breaks first in a fall and the person falls anyway.
  • A harness that has taken a fall can be used again. After one fall impact, the internal fibres may already be damaged — it must be retired.

Frequently Asked Questions

Is a safety harness the same thing as a safety rope?

No. A harness is the fall-protection gear worn on the body, and a rope connects the harness to the anchor point. The two must be used together — a rope alone cannot serve as a harness.

How do I choose between a full-body harness and a belt-type harness?

Choose a full-body harness for any work with a fall risk, so the fall force spreads across the body. A belt-type harness suits only work positioning and restraint, never fall arrest.

Can a harness be anchored to scaffolding?

It depends on whether the anchor is solid and can take the fall-arrest force. Never anchor to pipes, railings or moving parts that cannot bear the load, and keep the anchor as high as possible to shorten the fall distance.

How often should a harness be inspected?

Check the appearance before every use, do a full inspection every quarter, and a full test once a year under the standard. A harness or rope that has taken one fall must be retired at once, even if it looks undamaged.

WhatsApp 18300232331 Get a Free Quote
Chat Get a Quote