Category: Labor Protection Supplies

How to Choose Welding Gloves: Materials and Heat Resistance

Welding puts hands at multiple risks: burns from molten metal spatter, burns from arc heat radiation, burns from hot workpieces, cuts from sharp edges, and electric shock. Ordinary cotton yarn gloves and PU-coated gloves burn through in minutes on a welding site and offer no protection. Welding gloves are designed for welding — material, length and heat resistance all matter. This guide explains the selection points.

Know the Standard First: AQ 6103-2007 Is the Current Standard

The current industry standard for welder's protective gloves is AQ 6103-2007, Welder's Protective Gloves, issued 4 January 2007 and effective 1 April 2007. It applies to protective gloves used in manual metal welding, gas cutting and similar work, protecting the hands and wrists. The standard divides welder's protective gloves into Type A and Type B: Type A is low dexterity with higher other performance, suited to heavy welding; Type B is high dexterity with relatively lower other performance, suited to welding that needs fine operation.

Welding gloves must also meet mechanical hazard protection requirements under GB 24541-2022, Hand Protection — Mechanical Hazard Protective Gloves, covering abrasion, cut, tear and puncture resistance. The European standard EN 12477 is the international standard for welder's protective gloves, also divided into Type A and Type B, and can be referenced when buying export-type products.

When buying, note that welder's gloves should be made of wear-resistant, radiant-heat-resistant leather, or cotton canvas combined with leather, long enough to protect the wrist, and stitched firmly. Welders should not wear damaged or damp gloves for work.

How to Choose the Material

  • Cowhide: the most common welding glove material. Split cowhide is thick, wear-resistant, heat-resistant and spatter-resistant — the mainstream choice for heavy welding; grain cowhide is softer and more flexible, suited to welding that needs some dexterity. Cowhide gloves are durable, but a new pair feels stiff and needs breaking in.
  • Pigskin: softer and more breathable than cowhide, with higher dexterity, suited to TIG welding and other fine welding. But pigskin is less wear- and heat-resistant than cowhide, so it is not recommended for heavy welding.
  • Sheepskin: the softest and best-fitting, suited to fine welding, but relatively weaker in wear and heat resistance — only for light welding.
  • Canvas combined with leather: leather on key areas such as the palm, canvas on the back of the hand, combining protection and breathability, suited to long welding sessions.

The basic rule for material choice is: the heavier the welding and the more spatter, the thicker and more wear-resistant the material should be; the finer the operation, the softer and more flexible. Where the two conflict, protection comes first.

What to Look for in Heat Resistance

Heat resistance of welding gloves covers several aspects: flame resistance, contact heat protection, radiant heat protection and resistance to small splashes of molten metal. When selecting, look at the relevant items in the test report — do not just trust the words "heat-resistant".

  • Flame resistance: the glove material itself does not burn easily and does not keep burning after leaving the flame. Welding spatter landing on the glove should not ignite it.
  • Contact heat: the glove insulates against the residual heat of workpieces, so a freshly welded piece can be handled without burning. The thicker the lining, the better the insulation — but the worse the dexterity.
  • Radiant heat: arc heat radiation can burn the back of the hand, so the back of the glove needs enough protection.
  • Resistance to small splashes of molten metal: small droplets of molten metal spattering onto the glove should not burn through it or stick to it.

Also note: in welding places where conduction is possible, the gloves used should be made of materials with insulating properties. Damp gloves lose insulation, and welding with damp gloves carries a risk of electric shock.

Acceptance and Use

  • Check the length. Welding gloves are generally long, with an extended cuff that protects the wrist and forearm; short gloves leave the wrist exposed, where spatter can easily burn it.
  • Check the stitching. Seams should use heat-resistant fireproof thread — ordinary thread is burned through by spatter; the palm and back seams should be reinforced.
  • Check the size. Gloves must fit: too large and operation is clumsy and the glove can catch on equipment; too small and it pinches and breaks easily.
  • Check regularly. Replace gloves immediately when damaged, burned through, split at the seams or worn thin inside. A damaged glove on a welding site is the same as no glove.
  • Keep them dry in storage. Leather gloves go moldy and stiff when damp; store them somewhere ventilated and dry, out of direct sunlight.

Frequently Asked Questions

Welding gloves come in Type A and Type B — how do I choose?

Type A is low dexterity with higher other performance, suited to heavy welding and gas cutting; Type B is high dexterity, suited to TIG welding and other work needing fine operation. Choose by welding method and operating requirements.

Which is better, cowhide or pigskin gloves?

Neither is absolutely better — only more or less suited. Cowhide is thick, wear-resistant and heat-resistant, suited to heavy welding; pigskin is soft and flexible, suited to fine welding. Choose cowhide for heavy welding, and pigskin or sheepskin for fine work such as TIG welding.

Can welding gloves protect against electric shock?

Ordinary welding gloves are not insulating gloves and cannot replace them. In welding places where conduction is possible, choose gloves with insulating properties and keep them dry. Insulation for live work follows dedicated standards.

How often should welding gloves be replaced?

There is no fixed cycle — it depends on wear. Replace gloves immediately when they are damaged, burned through, split at the seams or worn thin inside. In heavy welding posts gloves wear out fast, so keep enough spares.

WhatsApp 18300232331 Get a Free Quote
Chat Get a Quote