Category: Labor Protection Supplies

How to Choose Safety Glasses: Impact and Splash Protection

Grinding, cutting, drilling, riveting, clearing debris — the most common eye injuries on industrial sites come from flying metal chips, wood chips, stones and dust. Eye injuries happen in an instant, and much of the damage is irreversible. Safety glasses look simple, but the wrong model is the same as no glasses: ordinary glasses cannot stop impact, and open-sided glasses cannot stop side splash. This guide explains the difference between safety glasses and goggles under the current standard, and how to choose by job hazard.

Know the Standard First: GB 14866-2023 Is the Current Version

The current mandatory national standard for eye and face protection in China is GB 14866-2023, General Technical Specification for Eye and Face Protection, published 28 December 2023 and in force from 1 January 2025, replacing GB 14866-2006, Technical Requirements for Personal Eye Protectors, and GB 32166.1-2016. Write the 2023 edition on purchase contracts and acceptance forms — the 2006 edition has been abolished.

The standard divides eye and face protection by shape into glasses, goggles and face shields, and sets requirements for optical performance, physical and mechanical performance, marking and more. Note its scope: GB 14866-2023 does not apply to welding protectors, auto-darkening welding filters, strong-light protectors, laser protectors or sunglasses. Eye and face protection for welding follows the GB/T 3609 series — a general pair of safety glasses must not be used against arc light. The standard also requires products to carry a permanent marking; be cautious of products with unclear or missing markings.

Glasses vs Goggles: Different Protection

Safety glasses are a frame plus lenses, light to wear with a good field of vision, suited to frontal low-energy impact and splash. Ordinary types only guard against slight frontal impact; types with side shields also guard against splash from the left and right, with clearly better protection. For grinding and cutting, where chips fly from all directions, choose a model with side shields.

Safety goggles seal all the way around the eyes with a soft material, so they stop large liquid splashes, dust and irritating gases entering through gaps. Acid and alkali work, spraying, dusty grinding, or any scene with liquid splash risk calls for goggles rather than ordinary glasses.

The basic selection rule is: "what it stops" is not enough — also ask "from which direction". If chips come only from the front, glasses are enough; if splash can come from the sides or below, or dust and liquid are involved, goggles are needed. When in doubt, choose the stricter protection.

Choose by Work Scene

  • Grinding, cutting, drilling, riveting: metal chips and grinding-wheel fragments fly at high speed — choose impact-rated safety glasses or goggles, with side shields or a sealed design better; heavy grinding calls for goggles plus a face shield.
  • Acid, alkali and chemical liquid work: liquid splash can enter the eyes from any direction — choose sealed goggles, and add a face shield for heavy splash.
  • Dusty work (woodworking, stone processing, sweeping): dust enters through glasses gaps — choose sealed goggles, and wear a dust mask as well.
  • Outdoor and high work: choose light, UV-protective safety glasses whose visible light transmittance is high enough that vision does not go dark.
  • Short-sighted staff: do not just put a pair of safety glasses over ordinary prescription glasses — choose safety glasses or goggles made to fit over prescription glasses, or lenses with prescription power.

For face shields, see How to Choose a Face Shield: Impact and Heat.

Acceptance and Use

  • Check the test report. The model, manufacturer and standard number on the report must match the delivered product, and the report must be within its validity period.
  • Inspect the lenses. Lens surfaces should be smooth, with no scratches or ripples; scratched or deformed lenses harm vision and impact resistance and should be replaced.
  • Check the fit. A goggle's sealing edge must fit the face, and the headband must adjust; glasses should sit without slipping or pressing on the nose. Glasses that are uncomfortable to wear will be taken off by workers looking for an excuse.
  • Keep lenses away from organic solvents. Ethanol, acetone, ethyl acetate, petroleum ether and similar solvents damage lenses — clean only with diluted detergent, then rinse with clean water and air dry.
  • Replace regularly. Replace scratched lenses, deformed frames and sealing edges that have aged and lost elasticity promptly — do not wait until they are completely broken.

Frequently Asked Questions

Can ordinary prescription glasses be used as safety glasses?

No. Ordinary glasses have not passed impact testing — under impact the lenses can shatter and cause a second injury. Short-sighted staff should choose safety glasses or goggles that fit over prescription glasses.

Can safety glasses and a face shield replace each other?

No. Glasses protect the eyes, a shield protects the whole face. A shield cannot replace glasses, because splash can reach the eyes from below or the sides of the shield; heavy-splash work calls for glasses plus shield worn together.

Do safety glasses need anti-fog?

In scenes with big temperature differences, high humidity or heavy physical work, lenses fog easily — and once fogged, workers take the glasses off to wipe them, which raises the injury risk. Such scenes call for models with an anti-fog coating or a ventilated design.

Can old stock under GB 14866-2006 still be bought?

GB 14866-2006 has been abolished; the current standard is GB 14866-2023. Purchase and acceptance should follow the 2023 edition, and old stock should be checked against the current standard's requirements.

WhatsApp 18300232331 Get a Free Quote
Chat Get a Quote